DCAN-100 Exam Training Practice Tests (Dell Networking Associate)]

Question 1

Refer to the output.

Which two actions occur if interface Tw2/0/2 goes down? (Choose two.)

A. Switch 3 remains in the stack. B. Switch 2 remains in the stack. C. Switch 1 becomes a standalone switch. D. Switch 2 becomes a standalone switch. E. Switch 3 becomes a standalone switch.

Correct Answer: A,B

Question 2

Which two methods will create a VLAN on N-Series switches? (Choose two.)

A. console(config)#interface vlan 11 B. console#vlan 11 C. console(config)#interface gi1/0/1console(config-if-Gi1/0/1)# vlan 10 D. console(config)#interface gi1/0/1console(config-if-Gi1/0/1)#switchport access vlan 10 E. console(config)#vlan 11

Correct Answer: D,E

Question 3

A technician configures RIP on a new N-Series switch to connect to an existing switch that runs RIP. The routing table is not populating even after the network statements are added.
What is a possible cause of this issue?

A. The other switch is not a root bridge and cannot form an RIP relationship. B. The "ip helper-address" command has not been configured on the existing switch. C. The new switch's interface is in the wrong subnet to form a RIP relationship. D. The existing switch has not been configured with the command "hostroutesaccept".

Correct Answer: C

Question 4

Refer to the output shown:
console (config-if-Tel/0/1) #switchport general allowed vlan add 2-6
console (config-if-Tel/0/1) #show interfaces switchport tengigabitethernet 1/0/1 Port: Tel/0/1 VLAN Membership Mode: General Mode Access Mode VLAN: 1 (default) General Mode PVID: 1 (default) General Mode Ingress Filtering: Enabled General Mode Acceptable Frame Type: Admit All General Mode Dynamically Added VLANs:
General Mode Untagged VLANs: 1-6
General Mode Tagged VLANs:
General Mode Forbidden VLANs:
Trunking Mode Native VLAN: 1 (default)
Trunking Mode Native VLAN Tagging: Disabled
Trunking Mode VLANs Enabled: All
Private VLAN Host Association: none
Private VLAN Mapping:
Private VLAN Operational Bindings:
Default Priority: 0
Protected: Disabled
Te1/0/1 interface must allow VLANs 2-6 and follow the 802.1Q standard.
Which change should be made to meet the requirements?

A. Add "tagged" command before VLAN ID B. Add "trunk" at the end of the command C. Add "802.1Q" at the end of the command D. Add "tagged" at the end of the command

Correct Answer: D

Question 5

Refer to the output from a Dell N-Series switch:

A technician checks the connectivity to the default gateway from the switch and notices the ping fails.
At which layer does the problem exist?

A. Session B. Transport C. Application D. Network

Correct Answer: D

Question 6

A Dell Networking N3024 has a link aggregation configured as shown:
interface Gi1/0/1
channel-group 1 mode active
exit
!
interface Gi1/0/2
channel-group 1 mode active
exit
!
interface port-channel 1
switchport access vlan 10
exit
After connecting all cables, the port-channel does NOT work as expected. As part of the troubleshooting process, the technician examines the "show lldp" displayed:

What is the most likely cause for the issue on the port-channel?

A. The interfaces are connected to different switches. B. The interface port-channel is not using 10Gbps interfaces. C. The interface port-channel is not configured in trunk mode. D. The interfaces on the N2024 switches are running LACP.

Correct Answer: A

Question 7

The "show ip ospf database" command outout indicates Type 5 LSAs.
What does presence of Type 5 LSA indicate?

A. A Description of destinations external to the AS B. An ABR existing in the network topology C. A Stub Area learned through an OSPF virtual-link D. A routing loop between multiple OSPF routers

Correct Answer: A

Dell Networking Associate - DCAN-100 Exam Practice Test