EMC Specialist - Implementation Engineer, Campus Networking - DES-5121 Exam Practice Test
When configuring a PBR route-map, what are the configurable "SET" options?
Correct Answer: C
Switch-1(config)# interface tengigabitethernet 1/0/1
Switch-1(config)# switchport mode access
Switch-1(config)# switchport trunk allowed vlan 10, 20
Switch-1(config)#
Switch-1(config)# interface tengigabitethernet 1/0/3
Switch-1(config)# switchport mode access
Switch-1(config)# switchport access vlan 10
Switch-2(config)# interface tengigabitethernet 1/0/2
Switch-2(config)# switchport mode trunk
Switch-2(config)# switchport trunk allowed vlan 10, 20
Switch-2(config)#
Switch-2(config)# interface tengigabitethernet 1/0/6
Switch-2(config)# switchport mode access
Switch-2(config)# switchport access vlan 20
A network administrator is troubleshooting why Host 1 cannot communicate with Host 2.
Based on the switch output shown in the exhibit, what is the reason for the communication issue?
Switch-1(config)# switchport mode access
Switch-1(config)# switchport trunk allowed vlan 10, 20
Switch-1(config)#
Switch-1(config)# interface tengigabitethernet 1/0/3
Switch-1(config)# switchport mode access
Switch-1(config)# switchport access vlan 10
Switch-2(config)# interface tengigabitethernet 1/0/2
Switch-2(config)# switchport mode trunk
Switch-2(config)# switchport trunk allowed vlan 10, 20
Switch-2(config)#
Switch-2(config)# interface tengigabitethernet 1/0/6
Switch-2(config)# switchport mode access
Switch-2(config)# switchport access vlan 20
A network administrator is troubleshooting why Host 1 cannot communicate with Host 2.
Based on the switch output shown in the exhibit, what is the reason for the communication issue?
Correct Answer: A
A network administrator is setting up a Class 5 powered device in their network.
Which Dell EMC N-Serves switch model(s) will support this device?
Which Dell EMC N-Serves switch model(s) will support this device?
Correct Answer: B
Based on the exhibit,
which configuration on interface Gi1/0/18 will allow the DHCP request to reach the DHCP server for the specified VLAN?
which configuration on interface Gi1/0/18 will allow the DHCP request to reach the DHCP server for the specified VLAN?
Correct Answer: C
An administrator just finished configuring a Dell EMC N-Series switch. After rebooting the switch, the administrator notices that all the configuration settings just entered are gone.
Which command did the administrator fail to enter?
Which command did the administrator fail to enter?
Correct Answer: B
Refer to the Exhibit.
Switch-1(config)# radius server host 10.1.1.111
Switch-1(config-radius)# key "secretkey"
Switch-1(config-radius)# exit
Switch-1(config)# aaa authentication login "LOCAL-AUTH" local
Switch-1(config)# aaa authentication login "REMOTE-AUTH" radius local
Switch-1(config)# aaa authentication enable "REMOTE-AUTH" radius enable Switch-1(config)# aaa authentication login default tacacs local Switch-1(config)# aaa authentication enable default tacacs enable Switch-1(config)# line telnet Switch-1(config-telnet)# login authentication "REMOTE-AUTH" Switch-1(config-telnet)# exit Switch-1(config)# line ssh Switch-1(config-ssh)# login authentication default Switch-1(config)# exit Switch-1(config)# line console Switch-1(config-line)# login authentication "LOCAL-AUTH" Switch-1(config-line)# exit Which authentication method will be used if a user tries to log into the switch when accessing through SSH?
Switch-1(config)# radius server host 10.1.1.111
Switch-1(config-radius)# key "secretkey"
Switch-1(config-radius)# exit
Switch-1(config)# aaa authentication login "LOCAL-AUTH" local
Switch-1(config)# aaa authentication login "REMOTE-AUTH" radius local
Switch-1(config)# aaa authentication enable "REMOTE-AUTH" radius enable Switch-1(config)# aaa authentication login default tacacs local Switch-1(config)# aaa authentication enable default tacacs enable Switch-1(config)# line telnet Switch-1(config-telnet)# login authentication "REMOTE-AUTH" Switch-1(config-telnet)# exit Switch-1(config)# line ssh Switch-1(config-ssh)# login authentication default Switch-1(config)# exit Switch-1(config)# line console Switch-1(config-line)# login authentication "LOCAL-AUTH" Switch-1(config-line)# exit Which authentication method will be used if a user tries to log into the switch when accessing through SSH?
Correct Answer: C
A customer is upgrading their campus network Access layer switches. They require 2-10GbE uplinks, 48- 1GbE ports with PoE, and stacking capability of up to 12 units.
Which Dell EMC N-Series model will meet the customer's requirements?
Which Dell EMC N-Series model will meet the customer's requirements?
Correct Answer: A
Explanation: Only visible for TrainingDump members. You can sign-up / login (it's free).