HP0-Y37 Exam Training Practice Tests (HP Migrating &Troubleshooting Enterprise Networks)]

Question 1

The ARP Inspection feature on Cisco devices is called ARP Detection or ARP Protection on HP A-Series and E-Series devices. Which statements are true about these ARP anti-spoofing mechanism? (Select three.)

A. ARP Detection/Inspection/Protection requires DHCP snooping to be enabled. B. ARP Detection/Inspection/Protection protects against "man in the middle" attacks from end nodes that spoof the IPX address of a node such as the default gateway in a VLAN. C. ARP Detection/Inspection/Protection inspects the content of the ARP packets generated by end nodes on untrusted ports and compares this content with the content of the MAC address table. D. ARP Detection/Inspection/Protection blocks IP traffic that is not formed with the right source IP address or source MAC address. E. ARP Detection/Inspection/Protection inspects the content of the ARP packets generated by end nodes on untrusted ports and compares this content with the content of the DHCP Snooping binding table. F. ARP Detection/Inspection/Protection was not designed to detect ARP packets that are malformed. G. ARP Detection/Inspection/Protection blocks ARP packets that are malformed on untrusted ports.

Correct Answer: A,E,G

Question 2

Click the Exhibit button.

Which statements are true about the BGP configuration of this HP A-Series router? (Select two.)

A. The router announces IP prefix 200.1.0.0/23 to its BGP neighbor if the network is in routing table. B. The BGP router will establish a BFD connection with its BGP neighbor 222.222.10.1 if the neighbor is also configured for BFD. C. The BGP router is in AS 200 and its BGP neighbor is in AS 100. D. The as-path ACL define networks that were last forwarded by AS 200. E. The configuration includes a filter out to the neighbor 222.222.10.1.

Correct Answer: A,B

Question 3

Click the Exhibit button and view the three exhibits.

When interface Serial 4 of Router 2 fails, traffic from Router 1 destined for network 156.152.0.0/16 leaves AS 65001 via the Serial 3 interface of Router 1. The administrator prefers that this traffic leaves AS 65001 through interface Serial 5 of Router 2. Which configuration change will achieve the desired results?

A. Router-1# route-policy Policy permit node 10 apply preferred-value 500 bgp 100 peer 16.0.0.2 route-policy Policy B. Router-2# route-policy Policy permit node 10 apply preferred-value 500 bgp 100 peer 156.152.5.1 route-policy Policy C. Router-2# bgp 100 peer 16.0.0.1 next-hop-local D. Router-2# route-policy Policy permit node 10 apply local-preference 500 bgp 100 peer 156.152.5.1 route-policy Policy

Correct Answer: C

Question 4

Click the Exhibit button.

You are in the process of replacing Cisco switches at the distribution layer with HP E-Series switches. At this point, you have removed one of the Cisco distribution switches so that only one remains in the network. You have also connected one HP E-Series switch in that switch's place. As shown in the exhibit, the HP E-Series switch connects to the distribution layer, the edge, and the core. To eliminate network loops, the Cisco switches implement Rapid Per-VLAN Spanning Tree Plus (Rapid PVST+), and the HP E-Series switch implements Multiple Spanning Tree Protocol (MSTP). (Each connection to the core is a member of a single VLAN that is dedicated to that connection only and does not participate in the spanning tree.) The exhibit also shows the current Spanning Tree topology. You are now ready to migrate Edge1 so that it is connected to the HP E-Series switch only. What happens when you disable P1 on Edge1?

A. Link 2 comes up in all VLANs after a several seconds because Edge1's Cisco uplinkfast feature does not interoperate with MSTP. B. Link 2 comes up in all VLANs after a few seconds when the HP E-Series switch opens its P2. C. Link 2 becomes active in VLAN 1, which interoperates with MSTP, but flaps on VLANs 10 and 20 because the HP E-Series switch blocks BPDUs on those VLANs. D. The loop that had existed on Link 2 in VLANs 10 and 20 is eliminated. Only after P2 on Edge1 recovers does the link come back up.

Correct Answer: B

Question 5

Click the Exhibit button and view a network diagram and a switch configuration.

What are possible node modes of Switch 6 in RRPP ring 3? (Select two.)

A. Edge B. Primary C. Slave D. Master E. Transit F. Assistant Edge G. Secondary

Correct Answer: A,F

Question 6

Click the Exhibit button and view the three exhibits.

Network 16.2.0.0 /16 is advertised by Router 1 and Router 2 into BGP. All traffic from AS-65002 destined to 16.2.0.0 /16 enters AS 65001 via the Serial 3 interface of Router 1. The administrator prefers that this traffic enter AS 65001 via interface Serial 4 of Router 2. Which configuration change is most likely to achieve the desired results?

A. Router-1#Router-1# route-policy PolicyB permit node 20 if-match ip-prefix Prefix2 apply cost 6000 route-policy PolicyB permit node 100 Router-2# route-policy PolicyB permit node 20 if-match ip-prefix Prefix2 apply cost 7000 route-policy PolicyB permit node 100 B. Router-1# route-policy PolicyA permit node 20 if-match ip-prefix Prefix2 apply cost 6000 route-policy PolicyA permit node 100 Router-2# route-policy PolicyA permit node 20 if-match ip-prefix Prefix2 apply cost 7000 route-policy PolicyA permit node 100 C. Router-1# route-policy PolicyA permit node 20 if-match ip-prefix Prefix2 apply cost 3000 route-policy PolicyA permit node 100 Router-2# route-policy PolicyA permit node 20 if-match ip-prefix Prefix2 apply cost 2000 route-policy PolicyA permit node 100 D. Router-1# route-policy PolicyB permit node 20 if-match ip-prefix Prefix2 apply cost 3000 route-policy PolicyB permit node 100 Router-2# route-policy PolicyB permit node 20 if-match ip-prefix Prefix2 apply cost 2000 route-policy PolicyB permit node 100

Correct Answer: D

Question 7

Click the Exhibit button and view the four exhibits.

You are replacing your Cisco distribution layer switches with HP E8212 zl switches. The Cisco switches have a VLAN map applied to VLAN 10 (subnet 10.1.10.0/24). The configuration for this VLAN map is as follows:

The exhibits display possible configurations for the HP ProVision ASIC-based E-Series switch. Which configuration controls traffic that arrives on VLAN 10 in the same way that the current Cisco switches do?

A. Exhibit 3 B. Exhibit 2 C. Exhibit 1 D. Exhibit 4

Correct Answer: A

Question 8

Click the Exhibit button and view a network diagram and two switch configurations.

After you issue the command irf-port-configuration active on HP A5800 Switch members 4 and 5, the 10 Gigabit Ethernet link 1/0/25 is connected. What is the expected result?

A. IRF Member 3 becomes the Master. B. IRF Member 2 becomes the Master. C. IRF Member 5 becomes the Master. D. IRF Member 4 becomes the Master.

Correct Answer: C

Question 9

Click the Exhibit button and view both exhibits.

You are configuring an HP A-Series switch so that the secure web traffic from the accounting, sales and development departments, is marked with 802.1p priorities 5, 3, and 4 respectively. Before you implement the following configuration, a peer reviewer informs you that there is an error in your configuration. Where in the configuration does this error reside?

A. access-list B. behavior C. policy D. classifier

Correct Answer: C

HP Migrating &Troubleshooting Enterprise Networks - HP0-Y37 Exam Practice Test