NS0-094 Exam Training Practice Tests (Network Appliance NetApp Hardware Support Engineer Professional)]

Question 1

After an unscheduled power outage, the storage system must be brought back online. What is the correct sequence of steps to power on and boot the system?

A. switches -> shelves -> controllers B. shelves -> controllers -> switches C. controllers -> shelves -> switches D. switches -> controllers -> shelves

Correct Answer: A

Question 2

A storage administrator is troubleshooting a 4-node cluster, where one node is reporting "cluster port is down" alerts. The node has recently been recabled to new cluster switches. The cluster ping-cluster command shows communication failures between the affected node and its partners over the cluster network. All physical cables have been verified as properly seated and undamaged. Which configuration is causing this problem?

A. The SVM data LIFs are on the wrong ports. B. An incorrect gateway is defined for the management network. C. An incorrect intercluster LIF is configured. D. The MTU size on the new cluster switches is mismatched with the nodes.

Correct Answer: D

Explanation: Only visible for TrainingDump members. You can sign-up / login (it's free).

Question 3

After you configure a new interface group with ports e2a and e2b, the ports are showing as down in the interface group.

Which two actions correct the issue? (Choose two.)

A. Ensure that the switch ports are correctly cabled. B. Verify the switch side LACP configuration. C. Modify ports e2a and e2b to -autonegotiate-admin false -speed-admin 40000. D. Add the ports e2a and e2b to broadcast domain bd_data1.

Correct Answer: A,B

Explanation: Only visible for TrainingDump members. You can sign-up / login (it's free).

Question 4

You need to upgrade your cluster switches to a new version of firmware. Which command do you use to prevent automatic case creation?

A. system node autosupport invoke -node * -type all -message STOP=5h B. system node autosupport invoke -node * -type all -message IGNORE=5h C. system node autosupport invoke -node * -type all -message MAINT=5h D. system node autosupport invoke -node * -type all -message SUPPRESS=5h

Correct Answer: C

Explanation: Only visible for TrainingDump members. You can sign-up / login (it's free).

Question 5

During power on, a memory error is diagnosed, and the system fails to boot NetApp ONTAP software. As AutoSupport is not enabled, a part must be requested from NetApp Support. What action do you take to address this issue?

A. Open a case through https://support.netapp.com. B. Boot into diagnostics mode. C. Log into NetApp ONTAP System Manager to gather details. D. Use NetApp Active IQ to drill down on the issue.

Correct Answer: B

Explanation: Only visible for TrainingDump members. You can sign-up / login (it's free).

Question 6

What is the default amount of time that a volume is available for recovery from the volume recovery queue following a volume deletion?

A. 12 hours B. 72 hours C. 24 hours D. 48 hours

Correct Answer: A

Explanation: Only visible for TrainingDump members. You can sign-up / login (it's free).

Question 7

A customer reports intermittent cluster communication failures after moving equipment to a new rack. Which issue is MOST likely?

A. Excessive aggregate snapshots B. Incorrect rack cabling or interconnect placement C. Disk encryption mismatch D. ONTAP licensing expiration

Correct Answer: B

Explanation: Only visible for TrainingDump members. You can sign-up / login (it's free).

Question 8

Which two statements regarding drive 1.2.3.L1 are true? (Choose two.)

A. The drive is in bay 2. B. The drive is in bay 3. C. The drive is in shelf 1. D. The drive is in shelf 2.

Correct Answer: B,D

Explanation: Only visible for TrainingDump members. You can sign-up / login (it's free).

Question 9

During an ONTAP upgrade, nodeA1 fails to boot. You notice that it is loading the previous version of ONTAP software. What step can be taken to boot the node successfully?

A. From the clustershell of the partner, run system node image modify to point to the correct version of ONTAP software. B. From the clustershell of nodeA1, run system node image modify to point to the correct version of ONTAP software. C. From the loader prompt of nodeA1, use setenv GX_PRIMARY_KERNEL_URL to point to the correct version of ONTAP software. D. From the loader prompt of nodeA1, run boot_backup to run the correct version of ONTAP software.

Correct Answer: C

Explanation: Only visible for TrainingDump members. You can sign-up / login (it's free).

Network Appliance NetApp Hardware Support Engineer Professional - NS0-094 Exam Practice Test