NS0-181 Exam Training Practice Tests (Network Appliance NetApp Certified Storage Installation Engineer

Question 1

A customer wants you to add a new AFF A700 HA pair to an existing 4-node AFF8080 EX cluster. The existing cluster uses netApp CN1610 switches for the cluster connection and is using the recommended port count.
Which statements is true in the scenario?

A. There are not enough ports available on the duster switch. B. You cannot mix different AFF models in the same duster. C. You cannot have more than four nodes with AFF. D. The AFF A7O0 is not supported with NelApp CN1610 switches.

Correct Answer: D

Question 2

Which two statements are true about the ONTAP 9.1 networking features.

A. The MTU will be the same across all ports in a broadcast domain. B. The broadcast domain is a layer 3 object. C. The MTU will change based on each port configuration ion broadcast domain D. The broadcast domain is a layer 2 object.

Correct Answer: C,D

Question 3

Click the Exhibit button.

After running Config Advisor 5.0 on a newly deployed ONTAP system, you are reviewing the output with the customer, and you find the warnings shown in the exhibit.
Which action should you perform before you leave the customer site?

A. Review the Hardware Universe Web site for calling guidance. B. Remove all of the SAS cables from behind the controllers and replace them with FC cables. C. Explain to the customer that the warnings are not relevant because of the quad-path HA cabling. D. Explain to the customer that Config Advisor does not support the AFF A700 and FAS900 systems.

Correct Answer: B

Question 4

You have just installed a new FAS2620 on a cluster site. You are using the USB cable for the intial configuration.
In this scenario, what is the default speed for the serial connection?

A. 115200 bps B. 576000 bps C. 15200 bps D. 9600 bps

Correct Answer: A

Question 5

You finished the installation of a 2-node cluster and want to determine whether HA is configured correctly.
What are two ways to accomplish this task? (Choose two.)

A. Use the cluster ha show and storage failover show commands on the CLI. B. Use the OnCommand System Manager GUI. C. Use the OnCommand Performance Manager GUI. D. Use the system node autosupport check show command on the CLI.

Correct Answer: A,B

Question 6

You are going to add a node to an existing cluster but first you must gather the appropriate information for the new node's management LIF.
What two pieces of information is required to accomplish this task? (Choose two.)

A. IP address B. NTP server address C. default gateway D. Service Processor Information

Correct Answer: A,C

Question 7

A customer ordered two new DS224C shelves. The customer wants you to add these shelves to an existing stack which consists of two DS2246 shelves.
Which statement is true in this scenario?

A. Mixing DS224C and DS2246 shelves in the same node are not supported. B. You need to order additional cables to expand the existing stack. C. You cannot mix DS224C and DS2246 shelves in the same stack. D. DS224C shelves are supports with only new HBAs.

Correct Answer: D

Question 8

A new AFF8200 has a four-port UTA2 adapter installed in slot 2. Using the ucadmin command, you see that these ports are configured for FC.
Which port names are correct in this scenario?

A. e2a/2a, e2b/2b, e2c/2c, e2d/2d B. e2a, e2b, e2c, e2d C. e0a/0a, e0b/0b, e0c/0c, e0d/od D. 2a, 2b, 2c, 2d

Correct Answer: D

Question 9

You have just installed a new FAS2650 HA for your customer. You are now configuring the NetApp AutoSupport transport section.
In this scenario, what is the NetApp best practice for this task to allow AutoSupport on Demand (ASOD)?

A. Use SMTP. B. Use HTTP. C. Use SSH. D. Use HTTPS.

Correct Answer: D

Network Appliance NetApp Certified Storage Installation Engineer - ONTAP 9.1 - NS0-181 Exam Practice Test