[Apr-2025] Verified AMPP Exam Dumps with Senior-Internal-Corrosion-Technologist Exam Study Guide
Best Quality AMPP Senior-Internal-Corrosion-Technologist Exam Questions TrainingDump Realistic Practice Exams [2025]
NEW QUESTION # 39
The most likely area of failure on a buried external pipeline coating is the:
- A. Ground bed
- B. Mainline coating
- C. Field Joint coating
- D. Areas exposed to Ultra Violet light
Answer: C
NEW QUESTION # 40
Centrifugal blast cleaning requires:
- A. Very large nozzles
- B. Well maintained blast wheels
- C. The use of single use abrasives
- D. A large volume of alt to propel the abrasive
Answer: B
NEW QUESTION # 41
When performing testing in accordance with ASTM D 2583 the Inspector may observe:
- A. Cold flow or creep
- B. Cohesion failure
- C. Adhesion failure
- D. Glue failure
Answer: A
NEW QUESTION # 42
II Is always possible to see moisture on a steel substrate:
- A. True
- B. False
Answer: B
NEW QUESTION # 43
A failure caused by applying a coating too thinly is known as
- A. cracking.
- B. chalking.
- C. failure to cure.
- D. pinholes.
Answer: D
NEW QUESTION # 44
You are a NACE Level 2 Coaling Inspector who has Just arrived on a Jobin progress where there Is no Inspection and Test Plan (UP). The first morning you arrive the Job is behind schedule and you are asked to take Dry Rim Thickness readings.
Your FIRST preferred course of action is to:
- A. Call your supervisor
- B. Refuseto take readings until an ITP isin place
- C. Use a generally accepted industry standard and proceed to take readings
- D. Develop your own methodology and proceed take the readings
Answer: B
NEW QUESTION # 45
All of these ate advantages of using repair patches EXCEPT
- A. barrier to moisture and corrosion.
- B. inert to common acids, alkalis, and solvents.
- C. special tools or equipment are required.
- D. excellent abrasion resistance.
Answer: C
NEW QUESTION # 46
When environmental enclosures ate being used an inspector needs to be concerned about:
- A. Structural integrity
- B. Lighting
- C. Air changes
- D. a), b), and c)
Answer: D
NEW QUESTION # 47
You are working as the only in-house NACE Level 2 Inspector in a shop setting when an independent 3rd party NACE Level 3 Inspector, representing the owner, presents you with a copy of a Non Conformance Report (NCR) he has written for a NACE2/SSPC SP 10 centrifugal blast which you had previously approved.
Your FIRST preferred course of action is to:
- A. Review the NCR with the other Inspector
- B. Verbally challenge the NCR
- C. Consult your supervisor
- D. Request a re-blast of the Item in question
Answer: A
NEW QUESTION # 48
When ASTM D 3363 Is specified the Inspector must:
- A. Use the correct solvent
- B. Record the highest value attained
- C. Record the two end points identified in the standard
- D. Record the percentage of failure
Answer: B
NEW QUESTION # 49
The Inspectors' goal at the Pre-Job Conference is to:
- A. Take accurate meeting minutes for distribution
- B. Discuss contractual requirements
- C. Obtain a clear understanding of the Specification
- D. Manage the meeting so it doesn't go off topic
Answer: C
NEW QUESTION # 50
Coating Surveys are legally required:
- A. On water tanks and potable water pipelines
- B. On food and beverage vessels and can linings
- C. On commercial marine vessels and offshore platforms
- D. On high pressure gas lines and fireproofed structures
Answer: C
NEW QUESTION # 51
The cost of qualified Coating Inspection Is normally offset by:
- A. Lower Coating Life Cycle Costs
- B. Lower Safety Enforcement Costs
- C. Lower Application Costs
- D. Lower Supervision Costs
Answer: A
NEW QUESTION # 52
When observing fabrication defects the NACE Inspector should:
- A. Stop the job immediately
- B. Consult the specification to determine how they should be treated
- C. Write an NCR and call the fabricator
- D. Require they be corrected prior to coating
Answer: B
NEW QUESTION # 53
When measuring the Dry Film Thickness of liquid coatings applied to galvanized ferrous substrates the most commonly used instrument Is the:
- A. Tooke Gauge
- B. Eddy Current Gauge
- C. Magnetic Gauge
- D. Ultra Sonic DFT Gauge
Answer: D
NEW QUESTION # 54
Dehumidification is defined as the removal of moisture vapor from the air to
- A. raise its relative humidity.
- B. lower Its temperature.
- C. provide worker comfort
- D. lower Its dew point.
Answer: D
NEW QUESTION # 55
Pre-cleaning of work pieces will NOT remove
- A. snow, ice or water.
- B. dirt.
- C. oil or grease.
- D. mill scale.
Answer: D
NEW QUESTION # 56
In which type of concrete are laitance commonly encountered?
- A. Concrete block (pouted with a form)
- B. Poured (wet cast)
- C. Glass fiber cement
- D. Gunite
Answer: B
NEW QUESTION # 57
Examples of non-ferrous metals include
Select All that Apply:
- A. iron
- B. aluminum
- C. mild steel.
- D. copper
Answer: B,C,D
NEW QUESTION # 58
......
Authentic Best resources for Senior-Internal-Corrosion-Technologist: https://www.trainingdump.com/AMPP/Senior-Internal-Corrosion-Technologist-practice-exam-dumps.html
Senior-Internal-Corrosion-Technologist Test Engine Practice Exam: https://drive.google.com/open?id=1QlSY1jk1tEjIHFcL_UsgfDIl5IRx_Ynk